Eaton LD2-681-HV 680.0 uH Metalized Inductor, Isat 0.44 A
Eaton LD2-681-HV 680.0 uH Metalized Inductor, Isat 0.44 A

Eaton LD2-681-HV 680.0 uH Metalized Inductor, Isat 0.44 A

Share
LD2-681-HV: metalized drum core inductor, 680.0 uH ±20%, 0.53 A, Isat 0.44 A, DCR 2500 mOhm.
    • Product Details
    • Download

    Eaton LD2-681-HV 680.0 uH Metalized Inductor, Isat 0.44 A

    LD2-681-HV at a glance: metalized drum core inductor, 680.0 uH ±20%, 0.53 A, Isat 0.44 A, DCR 2500 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberLD2-681-HV
    Inductance680.0 uH ±20%
    DCR maximum @ +25 °C2500 mOhm
    Irms (DC, 40 °C rise)0.53 A
    Isat0.44 A
    FLL minimum (at Isat)435 uH
    Impulse test voltage600 V
    Hi-pot test voltage1000 V
    MountingThrough-hole
    Operating temperature-25 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1200

    Mechanical Drawing

    LD2-681-HV mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1200: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    The drum geometry concentrates the field in the core but leaves the ends open, so the inductance depends on the surroundings more than a shielded part would. That is acceptable in the applications these parts serve – filters, bias supplies, low current DC-DC stages – where the board is not densely packed.

    At 0.53 A the winding dissipates about 0.702 W in copper, using the 2500 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 0.44 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the LD2 family this is value 36 of 41, in a range that runs from 1 to 2200 uH.

    What This Family Is For

    The drum core family covers about 1 µH to tens of microhenry in axial, radial and surface-mount bodies. It is the value range between the chip inductors and the large toroids.

    • The open magnetic path means nearby metal changes the inductance. Keep the specified clearance to shields and screws.
    • Typical applications: ac/dc direct buck converters; smart water heaters; smart home/kitchen appliances; smart heating systems/pumps; iot devices power converters.
    • Design note: the value tolerance is wide by design; do not build a resonant circuit around the nominal inductance without checking the band.

    Frequently Asked Questions

    Can it be used in a switching converter?
    Yes, within its current and frequency range. Check the core loss at the switching frequency before assuming the DC rating is the limit.

    What is the rated current based on?
    A defined temperature rise from DC current. At higher ambient the thermal margin shrinks, so derate against the actual board temperature.

    What is the rated current based on?
    A defined temperature rise from DC current. At higher ambient the thermal margin shrinks, so derate against the actual board temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products