Eaton LDS0705-R82M-R 0.861 nH Drum Core Inductor, 7.68 A
Eaton LDS0705-R82M-R 0.861 nH Drum Core Inductor, 7.68 A

Eaton LDS0705-R82M-R 0.861 nH Drum Core Inductor, 7.68 A

Share
LDS0705-R82M-R: metalized drum core inductor, 0.861 uH ±20%, 7.68 A, Isat 8.57 A, DCR 4 mOhm.
    • Product Details
    • Download

    Eaton LDS0705-R82M-R 0.861 nH Drum Core Inductor, 7.68 A

    LDS0705-R82M-R at a glance: metalized drum core inductor, 0.861 uH ±20%, 7.68 A, Isat 8.57 A, DCR 4 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberLDS0705-R82M-R
    Inductance0.861 nH ±20%
    DCR maximum @ +25 °C4 mOhm
    Irms (DC, 40 °C rise)7.68 A
    Isat8.57 A
    K-factor24.8
    Package7.8 x 7 x 5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4142

    Mechanical Dimensions & Pad Layout

    LDS0705-R82M-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4142: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    The drum geometry concentrates the field in the core but leaves the ends open, so the inductance depends on the surroundings more than a shielded part would. That is acceptable in the applications these parts serve – filters, bias supplies, low current DC-DC stages – where the board is not densely packed.

    At 7.68 A the winding dissipates about 0.236 W in copper, using the 4 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 8.57 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the LDS0705 family this is value 1 of 19, in a range that runs from 0.861 to 467 uH.

    What This Family Is For

    The drum core family covers about 1 µH to tens of microhenry in axial, radial and surface-mount bodies. It is the value range between the chip inductors and the large toroids.

    • The open magnetic path means nearby metal changes the inductance. Keep the specified clearance to shields and screws.
    • Typical applications: buck or boost inductor; noise filtering and output filter chokes; battery power, dc-dc converters; notebook and laptop power; hand held devices.
    • Design note: the value tolerance is wide by design; do not build a resonant circuit around the nominal inductance without checking the band.

    Frequently Asked Questions

    Can it be used in a switching converter?
    Yes, within its current and frequency range. Check the core loss at the switching frequency before assuming the DC rating is the limit.

    What is the rated current based on?
    A defined temperature rise from DC current. At higher ambient the thermal margin shrinks, so derate against the actual board temperature.

    Why use a drum core rather than a molded part?
    More inductance per unit cost in the mid range, and a wider value selection. The trade is a more open magnetic path and a larger body.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products