Eaton MCL1005-430-R 43.0 nH Chip Inductor, 100 Q
Eaton MCL1005-430-R 43.0 nH Chip Inductor, 100 Q

Eaton MCL1005-430-R 43.0 nH Chip Inductor, 100 Q

Share
MCL1005-430-R: multilayer chip inductor, 43.0 nH 200, Q 100, SRF 8 MHz, 1 mA, DCR 1100000 mOhm.
    • Product Details
    • Download

    Eaton MCL1005-430-R 43.0 nH Chip Inductor, 100 Q

    MCL1005-430-R at a glance: multilayer chip inductor, 43.0 nH 200, Q 100, SRF 8 MHz, 1 mA, DCR 1100000 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCL1005-430-R
    Inductance43.0 nH 200
    Q minimum100
    DCR maximum @ +25 °C1100000 mOhm
    Rated current maximum1 mA
    SRF minimum8 MHz
    Test frequency50 MHz
    Package1.0 x 0.5 mm
    Size code1005 (0402)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10925

    Mechanical Dimensions & Pad Layout

    MCL1005-430-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10925: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 43.0 nH 200 with a minimum Q of 100 at 50 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 100 means the part’s loss is about 1 % of its reactance in that band.

    Self-resonance is quoted as 8 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 8 MHz is the design headroom.

    Within the MCL1005 family this is value 34 of 46, in a range that runs from 0.001 to 0.36 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message