Eaton MCL1608V1-R10-R 0.1 nH Chip Inductor 0603
Eaton MCL1608V1-R10-R 0.1 nH Chip Inductor 0603

Eaton MCL1608V1-R10-R 0.1 nH Chip Inductor 0603

Share
MCL1608V1-R10-R: multilayer chip inductor, 0.1 nH , Q -, SRF 240 MHz, 150 mA, DCR 150 mOhm.
    • Product Details
    • Download

    Eaton MCL1608V1-R10-R 0.1 nH Chip Inductor 0603

    MCL1608V1-R10-R at a glance: multilayer chip inductor, 0.1 nH , Q -, SRF 240 MHz, 150 mA, DCR 150 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCL1608V1-R10-R
    Inductance0.1 nH
    DCR maximum @ +25 °C150 mOhm
    Rated current maximum150 mA
    SRF minimum240 MHz
    Test frequency1 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10926

    Mechanical Drawing

    MCL1608V1-R10-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10926: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    A multilayer chip inductor is a coil printed in layers of ceramic and metal, fired into a single body. There is no winding to buzz or shift, the inductance is set by the printed pattern, and the part sits on the board like any other 0402 or 0603 component. That construction is why these parts are used wherever the value is small and the quantity is large.

    The row reads 0.1 nH with a minimum Q of – at 1 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of – means the part’s loss is about 100 % of its reactance in that band.

    Self-resonance is quoted as 240 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 240 MHz is the design headroom.

    Within the MCL1608V1 family this is value 5 of 30, in a range that runs from 0.047 to 12 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products