Eaton MCL2012V1-R180-R 0.18 nH Chip Inductor 0805
Eaton MCL2012V1-R180-R 0.18 nH Chip Inductor 0805

Eaton MCL2012V1-R180-R 0.18 nH Chip Inductor 0805

Share
MCL2012V1-R180-R: multilayer chip inductor, 0.18 nH , Q -, SRF 185 MHz, 300 mA, DCR 250 mOhm.
    • Product Details
    • Download

    Eaton MCL2012V1-R180-R 0.18 nH Chip Inductor 0805

    MCL2012V1-R180-R at a glance: multilayer chip inductor, 0.18 nH , Q -, SRF 185 MHz, 300 mA, DCR 250 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCL2012V1-R180-R
    Inductance0.18 nH
    DCR maximum @ +25 °C250 mOhm
    Rated current maximum300 mA
    SRF minimum185 MHz
    Test frequency1 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10928

    Mechanical Drawing

    MCL2012V1-R180-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10928: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 0.18 nH with a minimum Q of – at 1 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of – means the part’s loss is about 100 % of its reactance in that band.

    Self-resonance is quoted as 185 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 185 MHz is the design headroom.

    Within the MCL2012V1 family this is value 8 of 33, in a range that runs from 0.047 to 22 nH.

    Positioning in the Range

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message