Eaton MCL2012V2-1R5-R 1.5 nH SMD Inductor, SRF 6000 MHz
Eaton MCL2012V2-1R5-R 1.5 nH SMD Inductor, SRF 6000 MHz

Eaton MCL2012V2-1R5-R 1.5 nH SMD Inductor, SRF 6000 MHz

Share
MCL2012V2-1R5-R: multilayer chip inductor, 1.5 nH ±0.3nH, Q 10, SRF 6000 MHz, 500 mA, DCR 100 mOhm.
    • Product Details
    • Download

    Eaton MCL2012V2-1R5-R 1.5 nH SMD Inductor, SRF 6000 MHz

    MCL2012V2-1R5-R at a glance: multilayer chip inductor, 1.5 nH ±0.3nH, Q 10, SRF 6000 MHz, 500 mA, DCR 100 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCL2012V2-1R5-R
    Inductance1.5 nH ±0.3nH
    Q minimum10
    DCR maximum @ +25 °C100 mOhm
    Rated current maximum500 mA
    SRF minimum6000 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10929

    Outline Drawing

    MCL2012V2-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10929: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    The inductance here is a few nanohenry, which puts the part in RF and high-speed digital territory: matching networks, filter sections, bias chokes on amplifier supplies, and the small isolation inductors that keep clock harmonics out of connectors. The multilayer body keeps the parasitics predictable, and the Q column tells you how much loss the part adds at the test frequency.

    The row reads 1.5 nH ±0.3nH with a minimum Q of 10 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 10 means the part’s loss is about 10 % of its reactance in that band.

    Self-resonance is quoted as 6000 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 6000 MHz is the design headroom.

    Within the MCL2012V2 family this is value 1 of 32, in a range that runs from 0.002 to 0.47 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communiations; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products