Eaton MCLA1005V2-5R6-R 5.6 nH Chip Inductor 0402
Eaton MCLA1005V2-5R6-R 5.6 nH Chip Inductor 0402

Eaton MCLA1005V2-5R6-R 5.6 nH Chip Inductor 0402

Share
MCLA1005V2-5R6-R: multilayer chip inductor, 5.6 nH ±0.3nH, Q 8, SRF 4000 MHz, 300 mA, DCR 250 mOhm.
    • Product Details
    • Download

    Eaton MCLA1005V2-5R6-R 5.6 nH Chip Inductor 0402

    MCLA1005V2-5R6-R at a glance: multilayer chip inductor, 5.6 nH ±0.3nH, Q 8, SRF 4000 MHz, 300 mA, DCR 250 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCLA1005V2-5R6-R
    Inductance5.6 nH ±0.3nH
    Q minimum8
    DCR maximum @ +25 °C250 mOhm
    Rated current maximum300 mA
    SRF minimum4000 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package1.0 x 0.5 mm
    Size code1005 (0402)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10974

    Mechanical Dimensions & Pad Layout

    MCLA1005V2-5R6-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10974: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    Where a circuit needs a small, stable inductance in a package measured in millimetres, the multilayer chip is the default. Its self-resonant frequency is the practical ceiling – above it the part behaves like a capacitor, so the SRF column is the first thing to check against the operating band.

    The row reads 5.6 nH ±0.3nH with a minimum Q of 8 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 8 means the part’s loss is about 12.5 % of its reactance in that band.

    Self-resonance is quoted as 4000 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 4000 MHz is the design headroom.

    Within the MCLA1005V2 family this is value 19 of 45, in a range that runs from 0.001 to 0.33 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antennas tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products