Eaton MCLA1608V1-3R9-R 3.9 uH SMD Inductor, SRF 35 MHz
Eaton MCLA1608V1-3R9-R 3.9 uH SMD Inductor, SRF 35 MHz

Eaton MCLA1608V1-3R9-R 3.9 uH SMD Inductor, SRF 35 MHz

Share
MCLA1608V1-3R9-R: multilayer chip inductor, 3.9 uH ±10, Q 25, SRF 35 MHz, 15 mA, DCR 1300 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V1-3R9-R 3.9 uH SMD Inductor, SRF 35 MHz

    MCLA1608V1-3R9-R at a glance: multilayer chip inductor, 3.9 uH ±10, Q 25, SRF 35 MHz, 15 mA, DCR 1300 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCLA1608V1-3R9-R
    Inductance3.9 uH ±10
    Q minimum25
    DCR maximum @ +25 °C1300 mOhm
    Rated current maximum15 mA
    SRF minimum35 MHz
    Test frequency10 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10975

    Mechanical Dimensions & Pad Layout

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10975; the package column above gives the body size in millimetres.

    What the Numbers Mean

    The inductance here is a few nanohenry, which puts the part in RF and high-speed digital territory: matching networks, filter sections, bias chokes on amplifier supplies, and the small isolation inductors that keep clock harmonics out of connectors. The multilayer body keeps the parasitics predictable, and the Q column tells you how much loss the part adds at the test frequency.

    The row reads 3.9 uH ±10 with a minimum Q of 25 at 10 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 25 means the part’s loss is about 4 % of its reactance in that band.

    Self-resonance is quoted as 35 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 35 MHz is the design headroom.

    Within the MCLA1608V1 family this is value 24 of 24, in a range that runs from 0.047 to 3.9 nH.

    Positioning in the Range

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products