Eaton MCLA1608V1-R680-R 0.68 nH Chip Inductor 0603
Eaton MCLA1608V1-R680-R 0.68 nH Chip Inductor 0603

Eaton MCLA1608V1-R680-R 0.68 nH Chip Inductor 0603

Share
MCLA1608V1-R680-R: multilayer chip inductor, 0.68 nH ±10, Q 20, SRF 90 MHz, 50 mA, DCR 900 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V1-R680-R 0.68 nH Chip Inductor 0603

    MCLA1608V1-R680-R at a glance: multilayer chip inductor, 0.68 nH ±10, Q 20, SRF 90 MHz, 50 mA, DCR 900 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCLA1608V1-R680-R
    Inductance0.68 nH ±10
    Q minimum20
    DCR maximum @ +25 °C900 mOhm
    Rated current maximum50 mA
    SRF minimum90 MHz
    Test frequency25 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10975

    Mechanical Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10975; the package column above gives the body size in millimetres.

    How to Read These Ratings

    A multilayer chip inductor is a coil printed in layers of ceramic and metal, fired into a single body. There is no winding to buzz or shift, the inductance is set by the printed pattern, and the part sits on the board like any other 0402 or 0603 component. That construction is why these parts are used wherever the value is small and the quantity is large.

    The row reads 0.68 nH ±10 with a minimum Q of 20 at 25 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 20 means the part’s loss is about 5 % of its reactance in that band.

    Self-resonance is quoted as 90 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 90 MHz is the design headroom.

    Within the MCLA1608V1 family this is value 15 of 24, in a range that runs from 0.047 to 3.9 nH.

    Series Positioning

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products