Eaton MCLA1608V2-1R0-R 1.0 nH Chip Inductor 0603
Eaton MCLA1608V2-1R0-R 1.0 nH Chip Inductor 0603

Eaton MCLA1608V2-1R0-R 1.0 nH Chip Inductor 0603

Share
MCLA1608V2-1R0-R: multilayer chip inductor, 1.0 nH ±0.3nH, Q 8, SRF 10000 MHz, 500 mA, DCR 50 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V2-1R0-R 1.0 nH Chip Inductor 0603

    MCLA1608V2-1R0-R at a glance: multilayer chip inductor, 1.0 nH ±0.3nH, Q 8, SRF 10000 MHz, 500 mA, DCR 50 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCLA1608V2-1R0-R
    Inductance1.0 nH ±0.3nH
    Q minimum8
    DCR maximum @ +25 °C50 mOhm
    Rated current maximum500 mA
    SRF minimum10000 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10976

    Mechanical Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10976; the package column above gives the body size in millimetres.

    The Figures Explained

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 1.0 nH ±0.3nH with a minimum Q of 8 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 8 means the part’s loss is about 12.5 % of its reactance in that band.

    Self-resonance is quoted as 10000 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 10000 MHz is the design headroom.

    Within the MCLA1608V2 family this is value 1 of 34, in a range that runs from 0.001 to 0.47 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products