Eaton MCLA1608V2-1R2-R 1.2 nH SMD Inductor, SRF 10000 MHz
Eaton MCLA1608V2-1R2-R 1.2 nH SMD Inductor, SRF 10000 MHz

Eaton MCLA1608V2-1R2-R 1.2 nH SMD Inductor, SRF 10000 MHz

Share
MCLA1608V2-1R2-R: multilayer chip inductor, 1.2 nH ±0.3nH, Q 8, SRF 10000 MHz, 500 mA, DCR 50 mOhm.
    • Product Details
    • Download

    Eaton MCLA1608V2-1R2-R 1.2 nH SMD Inductor, SRF 10000 MHz

    MCLA1608V2-1R2-R at a glance: multilayer chip inductor, 1.2 nH ±0.3nH, Q 8, SRF 10000 MHz, 500 mA, DCR 50 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCLA1608V2-1R2-R
    Inductance1.2 nH ±0.3nH
    Q minimum8
    DCR maximum @ +25 °C50 mOhm
    Rated current maximum500 mA
    SRF minimum10000 MHz
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10976

    Outline Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10976; the package column above gives the body size in millimetres.

    How to Read These Ratings

    The inductance here is a few nanohenry, which puts the part in RF and high-speed digital territory: matching networks, filter sections, bias chokes on amplifier supplies, and the small isolation inductors that keep clock harmonics out of connectors. The multilayer body keeps the parasitics predictable, and the Q column tells you how much loss the part adds at the test frequency.

    The row reads 1.2 nH ±0.3nH with a minimum Q of 8 at 100 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 8 means the part’s loss is about 12.5 % of its reactance in that band.

    Self-resonance is quoted as 10000 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 10000 MHz is the design headroom.

    Within the MCLA1608V2 family this is value 2 of 34, in a range that runs from 0.001 to 0.47 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products