Eaton MCLA2012V1-R820-R 0.82 nH SMD Inductor, SRF 100 MHz
Eaton MCLA2012V1-R820-R 0.82 nH SMD Inductor, SRF 100 MHz

Eaton MCLA2012V1-R820-R 0.82 nH SMD Inductor, SRF 100 MHz

Share
MCLA2012V1-R820-R: multilayer chip inductor, 0.82 nH ±10, Q 25, SRF 100 MHz, 150 mA, DCR 700 mOhm.
    • Product Details
    • Download

    Eaton MCLA2012V1-R820-R 0.82 nH SMD Inductor, SRF 100 MHz

    MCLA2012V1-R820-R at a glance: multilayer chip inductor, 0.82 nH ±10, Q 25, SRF 100 MHz, 150 mA, DCR 700 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMCLA2012V1-R820-R
    Inductance0.82 nH ±10
    Q minimum25
    DCR maximum @ +25 °C700 mOhm
    Rated current maximum150 mA
    SRF minimum100 MHz
    Test frequency25 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10977

    Mechanical Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10977; the package column above gives the body size in millimetres.

    Reading the Data Sheet

    Where a circuit needs a small, stable inductance in a package measured in millimetres, the multilayer chip is the default. Its self-resonant frequency is the practical ceiling – above it the part behaves like a capacitor, so the SRF column is the first thing to check against the operating band.

    The row reads 0.82 nH ±10 with a minimum Q of 25 at 25 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 25 means the part’s loss is about 4 % of its reactance in that band.

    Self-resonance is quoted as 100 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 100 MHz is the design headroom.

    Within the MCLA2012V1 family this is value 16 of 30, in a range that runs from 0.047 to 12 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    How much does the value drift with temperature?
    The data sheet gives the tolerance band; the drift inside that band is small for this construction because there is no mechanical winding to move.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products