Eaton MCLA3225V1-3R3-R 3.3 uH Chip Inductor 1210
Eaton MCLA3225V1-3R3-R 3.3 uH Chip Inductor 1210

Eaton MCLA3225V1-3R3-R 3.3 uH Chip Inductor 1210

Share
MCLA3225V1-3R3-R: multilayer chip inductor, 3.3 uH ±10, Q 40, SRF 50 MHz, 500 mA, DCR 400 mOhm.
    • Product Details
    • Download

    Eaton MCLA3225V1-3R3-R 3.3 uH Chip Inductor 1210

    MCLA3225V1-3R3-R at a glance: multilayer chip inductor, 3.3 uH ±10, Q 40, SRF 50 MHz, 500 mA, DCR 400 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCLA3225V1-3R3-R
    Inductance3.3 uH ±10
    Q minimum40
    DCR maximum @ +25 °C400 mOhm
    Rated current maximum500 mA
    SRF minimum50 MHz
    Test frequency10 MHz
    Test voltage50 mV
    Package3.2 x 2.5 mm
    Size code3225 (1210)
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10979

    Mechanical Drawing

    Outline drawing and pad layout are on page 2 of Eaton Technical Data 10979; the package column above gives the body size in millimetres.

    Reading the Data Sheet

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 3.3 uH ±10 with a minimum Q of 40 at 10 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 40 means the part’s loss is about 2.5 % of its reactance in that band.

    Self-resonance is quoted as 50 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 50 MHz is the design headroom.

    Within the MCLA3225V1 family this is value 7 of 14, in a range that runs from 1 to 12 nH.

    Where This Series Fits

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: adas; infotainment; wireless communications; wifi, bluetooth, satellite; antenna tuning.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products