Eaton MCQ1V1608-R470-R 0.47 nH Chip Inductor 0603
Eaton MCQ1V1608-R470-R 0.47 nH Chip Inductor 0603

Eaton MCQ1V1608-R470-R 0.47 nH Chip Inductor 0603

Share
MCQ1V1608-R470-R: multilayer chip inductor, 0.47 nH ±10, Q 20, SRF 105 MHz, 50 mA, DCR 700 mOhm.
    • Product Details
    • Download

    Eaton MCQ1V1608-R470-R 0.47 nH Chip Inductor 0603

    MCQ1V1608-R470-R at a glance: multilayer chip inductor, 0.47 nH ±10, Q 20, SRF 105 MHz, 50 mA, DCR 700 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMCQ1V1608-R470-R
    Inductance0.47 nH ±10
    Q minimum20
    DCR maximum @ +25 °C700 mOhm
    Rated current maximum50 mA
    SRF minimum105 MHz
    Test frequency25 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11101

    Mechanical Dimensions & Pad Layout

    MCQ1V1608-R470-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11101: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 0.47 nH ±10 with a minimum Q of 20 at 25 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 20 means the part’s loss is about 5 % of its reactance in that band.

    Self-resonance is quoted as 105 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 105 MHz is the design headroom.

    Within the MCQ1V1608 family this is value 13 of 24, in a range that runs from 0.047 to 3.9 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products