Eaton MCQ1V2012-1R5-R 1.5 uH SMD Inductor, SRF 60 MHz
Eaton MCQ1V2012-1R5-R 1.5 uH SMD Inductor, SRF 60 MHz

Eaton MCQ1V2012-1R5-R 1.5 uH SMD Inductor, SRF 60 MHz

Share
MCQ1V2012-1R5-R: multilayer chip inductor, 1.5 uH ±10, Q 35, SRF 60 MHz, 50 mA, DCR 400 mOhm.
    • Product Details
    • Download

    Eaton MCQ1V2012-1R5-R 1.5 uH SMD Inductor, SRF 60 MHz

    MCQ1V2012-1R5-R at a glance: multilayer chip inductor, 1.5 uH ±10, Q 35, SRF 60 MHz, 50 mA, DCR 400 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMCQ1V2012-1R5-R
    Inductance1.5 uH ±10
    Q minimum35
    DCR maximum @ +25 °C400 mOhm
    Rated current maximum50 mA
    SRF minimum60 MHz
    Test frequency10 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11103

    Mechanical Drawing

    MCQ1V2012-1R5-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11103: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a surface-mount multilayer inductor: printed coil, sintered body, silver terminations. The value is quoted at a defined test frequency because at these inductances the measurement conditions matter as much as the part.

    The row reads 1.5 uH ±10 with a minimum Q of 35 at 10 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 35 means the part’s loss is about 2.86 % of its reactance in that band.

    Self-resonance is quoted as 60 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 60 MHz is the design headroom.

    Within the MCQ1V2012 family this is value 19 of 25, in a range that runs from 0.047 to 4.7 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    What happens above the self-resonant frequency?
    The part becomes capacitive. Any filter or matching design has to keep the operating band below SRF, with margin for the tolerance of the value.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products