Eaton MCQ1V2012-R680-R 0.68 nH SMD Inductor, SRF 105 MHz
Eaton MCQ1V2012-R680-R 0.68 nH SMD Inductor, SRF 105 MHz

Eaton MCQ1V2012-R680-R 0.68 nH SMD Inductor, SRF 105 MHz

Share
MCQ1V2012-R680-R: multilayer chip inductor, 0.68 nH ±10, Q 25, SRF 105 MHz, 150 mA, DCR 650 mOhm.
    • Product Details
    • Download

    Eaton MCQ1V2012-R680-R 0.68 nH SMD Inductor, SRF 105 MHz

    MCQ1V2012-R680-R at a glance: multilayer chip inductor, 0.68 nH ±10, Q 25, SRF 105 MHz, 150 mA, DCR 650 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMCQ1V2012-R680-R
    Inductance0.68 nH ±10
    Q minimum25
    DCR maximum @ +25 °C650 mOhm
    Rated current maximum150 mA
    SRF minimum105 MHz
    Test frequency25 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11103

    Mechanical Drawing

    MCQ1V2012-R680-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11103: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    What the Numbers Mean

    A multilayer chip inductor is a coil printed in layers of ceramic and metal, fired into a single body. There is no winding to buzz or shift, the inductance is set by the printed pattern, and the part sits on the board like any other 0402 or 0603 component. That construction is why these parts are used wherever the value is small and the quantity is large.

    The row reads 0.68 nH ±10 with a minimum Q of 25 at 25 MHz. Q is the ratio of reactance to resistance at that frequency, so a Q of 25 means the part’s loss is about 4 % of its reactance in that band.

    Self-resonance is quoted as 105 MHz minimum. Below it the part is inductive; above it the inter-layer capacitance takes over. The margin between the operating band and 105 MHz is the design headroom.

    Within the MCQ1V2012 family this is value 15 of 25, in a range that runs from 0.047 to 4.7 nH.

    What This Family Is For

    The multilayer chip family covers nanohenry to a few microhenry values in 0402 through 1812 bodies. It is the range where the inductance is too small for a wound part to be practical and where the self-resonant frequency sets the usable band.

    • The rated current is a thermal limit for the part in free air, not a saturation limit. At high ambient the current has to be derated.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: compare SRF against the highest frequency the circuit will see, not just the fundamental.

    Frequently Asked Questions

    Why is the inductance quoted at a test frequency?
    At nanohenry values the parasitic capacitance and the measurement fixture both matter. The value is only meaningful at the frequency stated, and the Q column tells you how much of the reactance is loss at that point.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Can I replace a wire-wound chip with this part?
    Only if the Q and the current rating suit the circuit. Multilayer parts have lower Q and lower current capability than wire-wound parts of the same size.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products