Eaton MFBA2V2012P-111-R 110 Ohm Ferrite Bead 0805
Eaton MFBA2V2012P-111-R 110 Ohm Ferrite Bead 0805

Eaton MFBA2V2012P-111-R 110 Ohm Ferrite Bead 0805

Share
MFBA2V2012P-111-R: multilayer ferrite bead, 110 Ohm at 100 MHz, 5000 mA, DCR 13 mOhm.
    • Product Details
    • Download

    Eaton MFBA2V2012P-111-R 110 Ohm Ferrite Bead 0805

    MFBA2V2012P-111-R at a glance: multilayer ferrite bead, 110 Ohm at 100 MHz, 5000 mA, DCR 13 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMFBA2V2012P-111-R
    Impedance @ 100 MHz110 Ohm
    DCR maximum @ +25 °C13 mOhm
    Rated current maximum5000 mA
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-55 °C to +150 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1132

    Mechanical Drawing

    MFBA2V2012P-111-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1132: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 110 ohm, and its DC resistance is 13 mOhm maximum. At the rated 5000 mA that resistance drops 0.065 V, which is the figure to check against the rail tolerance.

    Within the MFBA2V2012P family this is value 2 of 6, in a range that runs from 0 to 0 nH.

    Series Positioning

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: body electronics (keyless entry, ecu, antennas); advanced driver assistance systems (adas); infotainment and cluster electronics; safety electronics systems; wlan, wifi, bluetooth.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products