Eaton MFBA3V1608H-202-R 2000 Ohm Ferrite Bead, 150 mA
Eaton MFBA3V1608H-202-R 2000 Ohm Ferrite Bead, 150 mA

Eaton MFBA3V1608H-202-R 2000 Ohm Ferrite Bead, 150 mA

Share
MFBA3V1608H-202-R: multilayer ferrite bead, 2000 Ohm at 100 MHz, 150 mA, DCR 1200 mOhm.
    • Product Details
    • Download

    Eaton MFBA3V1608H-202-R 2000 Ohm Ferrite Bead, 150 mA

    MFBA3V1608H-202-R at a glance: multilayer ferrite bead, 2000 Ohm at 100 MHz, 150 mA, DCR 1200 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMFBA3V1608H-202-R
    Impedance @ 100 MHz2000 Ohm
    DCR maximum @ +25 °C1200 mOhm
    Rated current maximum150 mA
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-55 °C to +150 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data ELX1328

    Dimensions and Pad Layout

    MFBA3V1608H-202-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data ELX1328: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 2000 ohm, and its DC resistance is 1200 mOhm maximum. At the rated 150 mA that resistance drops 0.18 V, which is the figure to check against the rail tolerance.

    Within the MFBA3V1608H family this is value 2 of 2, in a range that runs from 0 to 0 nH.

    What This Family Is For

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: body electronics (keyless entry, ecu, antennas); advanced driver assistance systems (adas); infotainment and cluster electronics; safety electronics systems; wlan, wifi, bluetooth.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products