Eaton MFBM1V1608-101-R 100 Ohm Multilayer Chip Bead
Eaton MFBM1V1608-101-R 100 Ohm Multilayer Chip Bead

Eaton MFBM1V1608-101-R 100 Ohm Multilayer Chip Bead

Share
MFBM1V1608-101-R: multilayer ferrite bead, 100 Ohm at 100 MHz, 2500 mA, DCR 60 mOhm.
    • Product Details
    • Download

    Eaton MFBM1V1608-101-R 100 Ohm Multilayer Chip Bead

    MFBM1V1608-101-R at a glance: multilayer ferrite bead, 100 Ohm at 100 MHz, 2500 mA, DCR 60 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMFBM1V1608-101-R
    Impedance @ 100 MHz100 Ohm
    Impedance tolerance±25%
    DCR maximum @ +25 °C60 mOhm
    Rated current maximum2500 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11111

    Mechanical Dimensions & Pad Layout

    MFBM1V1608-101-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11111: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    Beads are placed in series with a supply or signal line to take the high-frequency edge off it. The rated current and the DCR decide whether the part can sit in a power path; the impedance decides how much noise it removes.

    At 100 MHz this bead presents 100 ohm with an allowed spread of ±25%, and its DC resistance is 60 mOhm maximum. At the rated 2500 mA that resistance drops 0.15 V, which is the figure to check against the rail tolerance.

    Within the MFBM1V1608 family this is value 14 of 23, in a range that runs from 0 to 0 nH.

    What This Family Is For

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antennas.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products