Eaton MFBM1V1608-190-R 19 Ohm Ferrite Bead 0603
Eaton MFBM1V1608-190-R 19 Ohm Ferrite Bead 0603

Eaton MFBM1V1608-190-R 19 Ohm Ferrite Bead 0603

Share
MFBM1V1608-190-R: multilayer ferrite bead, 19 Ohm at 100 MHz, 5000 mA, DCR 30 mOhm.
    • Product Details
    • Download

    Eaton MFBM1V1608-190-R 19 Ohm Ferrite Bead 0603

    MFBM1V1608-190-R at a glance: multilayer ferrite bead, 19 Ohm at 100 MHz, 5000 mA, DCR 30 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMFBM1V1608-190-R
    Impedance @ 100 MHz19 Ohm
    Impedance tolerance12~25 Ω
    DCR maximum @ +25 °C30 mOhm
    Rated current maximum5000 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11111

    Dimensions and Pad Layout

    MFBM1V1608-190-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11111: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    The Figures Explained

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 19 ohm with an allowed spread of 12~25 Ω, and its DC resistance is 30 mOhm maximum. At the rated 5000 mA that resistance drops 0.15 V, which is the figure to check against the rail tolerance.

    Within the MFBM1V1608 family this is value 7 of 23, in a range that runs from 0 to 0 nH.

    What This Family Is For

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antennas.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message