Eaton MFBW1V1608-121-R 120 Ohm SMD Bead, 1000 mA
Eaton MFBW1V1608-121-R 120 Ohm SMD Bead, 1000 mA

Eaton MFBW1V1608-121-R 120 Ohm SMD Bead, 1000 mA

Share
MFBW1V1608-121-R: multilayer ferrite bead, 120 Ohm at 100 MHz, 1000 mA, DCR 150 mOhm.
    • Product Details
    • Download

    Eaton MFBW1V1608-121-R 120 Ohm SMD Bead, 1000 mA

    MFBW1V1608-121-R at a glance: multilayer ferrite bead, 120 Ohm at 100 MHz, 1000 mA, DCR 150 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberMFBW1V1608-121-R
    Impedance @ 100 MHz120 Ohm
    Impedance tolerance±25%
    DCR maximum @ +25 °C150 mOhm
    Rated current maximum1000 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package1.6 x 0.8 mm
    Size code1608 (0603)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11107

    Mechanical Dimensions & Pad Layout

    MFBW1V1608-121-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11107: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    What the Numbers Mean

    A ferrite bead is not an inductor in the usual sense: it is a lossy element. At low frequency it looks like a small resistance in series with the line; at the frequency where the ferrite absorbs, its impedance rises and the noise energy is converted into heat in the material rather than reflected back into the circuit.

    At 100 MHz this bead presents 120 ohm with an allowed spread of ±25%, and its DC resistance is 150 mOhm maximum. At the rated 1000 mA that resistance drops 0.15 V, which is the figure to check against the rail tolerance.

    Within the MFBW1V1608 family this is value 16 of 28, in a range that runs from 0 to 0 nH.

    Where This Series Fits

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products