Eaton MFBW1V2012-202-R 2000 Ohm Ferrite Bead 0805
Eaton MFBW1V2012-202-R 2000 Ohm Ferrite Bead 0805

Eaton MFBW1V2012-202-R 2000 Ohm Ferrite Bead 0805

Share
MFBW1V2012-202-R: multilayer ferrite bead, 2000 Ohm at 100 MHz, 300 mA, DCR 500 mOhm.
    • Product Details
    • Download

    Eaton MFBW1V2012-202-R 2000 Ohm Ferrite Bead 0805

    MFBW1V2012-202-R at a glance: multilayer ferrite bead, 2000 Ohm at 100 MHz, 300 mA, DCR 500 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMFBW1V2012-202-R
    Impedance @ 100 MHz2000 Ohm
    Impedance tolerance±25%
    DCR maximum @ +25 °C500 mOhm
    Rated current maximum300 mA
    Test frequency100 MHz
    Test voltage50 mV
    Package2.0 x 1.25 mm
    Size code2012 (0805)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 11108

    Mechanical Drawing

    MFBW1V2012-202-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 11108: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    Reading the Data Sheet

    This is a multilayer chip bead: ferrite sheets printed with internal electrodes, fired into one body. The impedance comes from the magnetic material, not from a winding, so the part stays effective at frequencies where a wire-wound bead would have already turned capacitive.

    At 100 MHz this bead presents 2000 ohm with an allowed spread of ±25%, and its DC resistance is 500 mOhm maximum. At the rated 300 mA that resistance drops 0.15 V, which is the figure to check against the rail tolerance.

    Within the MFBW1V2012 family this is value 27 of 27, in a range that runs from 0 to 0 nH.

    Series Positioning

    The ferrite bead family spans a few ohms to several hundred ohms at 100 MHz, in 0201 through 1206 bodies. Current ratings run from a few hundred milliamps in the small sizes to several amps in the larger ones.

    • A bead in a power path drops DC volts according to its DCR. Check that drop against the rail tolerance before choosing a high-impedance part.
    • Typical applications: industrial connectivity (iot); wireless communications; bluetooth; wifi; antenna.
    • Design note: pick the bead from the impedance curve at the failing frequency, then check the DC current and DCR for the line it sits in.

    Frequently Asked Questions

    Is impedance at 100 MHz the whole story?
    No. It is the specified reference point, but the impedance curve falls away on both sides. A bead chosen for a 100 MHz figure may be weak at the 30 MHz harmonic that is actually failing EMC.

    How do I choose between MFBM and MFBW?
    MFBM is the high-current series: lower impedance per size, higher rated current. MFBW is the high-impedance series for signal lines where DC current is small.

    What does the impedance tolerance mean?
    It is the allowed spread around the nominal impedance. Low-value beads are specified as a range, for example 0 to 15 ohm, because a percentage tolerance at those values would be meaningless.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products