Eaton MLVA02V05C033 5.5 V Multilayer Varistor
Eaton MLVA02V05C033 5.5 V Multilayer Varistor

Eaton MLVA02V05C033 5.5 V Multilayer Varistor

Share
MLVA02V05C033: multilayer varistor ESD suppressor, 8-14 V varistor voltage, 5.5 V working, 30 V clamp, 33 pF.
    • Product Details
    • Download

    Eaton MLVA02V05C033 5.5 V Multilayer Varistor

    MLVA02V05C033 at a glance: multilayer varistor ESD suppressor, 8-14 V varistor voltage, 5.5 V working, 30 V clamp, 33 pF.

    Key Specifications

    ParameterValue
    Orderable part numberMLVA02V05C033
    Package size0201
    Working voltage, RMS4 Vrms
    Working voltage, DC5.5 Vdc
    Varistor voltage at 1 mA8-14 V
    Clamping voltage30 V
    Typical capacitance33 pF
    Package0201 (0603 metric)
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 4070

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    A multilayer varistor sits across a signal or supply rail and does nothing until the voltage crosses its breakdown point, at which it turns into a low impedance and diverts the transient. The value that matters for the protected chip is not the varistor voltage but the clamping voltage at the surge current you expect.

    The clamp column works out at 3.75 times the varistor voltage: 30 V at the rated current against 8-14 V at 1 mA. That ratio is what the downstream part has to survive, not the 8-14 V figure on the label.

    The 33 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVA family this is item 1 of 12 in the Eaton catalogue.

    Where This Series Fits

    The part goes across the line it protects, as close to the connector or the cable entry as the layout allows. Lead length matters: every extra millimetre of trace between the connector and the varistor adds inductance and raises the voltage the protected chip actually sees.

    • The energy rating assumes a single pulse. Repeating the same transient heats the body faster than the datasheet curve suggests, because the curve is drawn for one event at a time.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products