Eaton MLVC08V012C220 Multilayer Varistor, 34 V Clamp
Eaton MLVC08V012C220 Multilayer Varistor, 34 V Clamp

Eaton MLVC08V012C220 Multilayer Varistor, 34 V Clamp

Share
MLVC08V012C220: multilayer varistor ESD suppressor, 18 V varistor voltage, 12 V working, 34 V clamp, 220 pF, 0.1 J.
    • Product Details
    • Download

    Eaton MLVC08V012C220 Multilayer Varistor, 34 V Clamp

    MLVC08V012C220 at a glance: multilayer varistor ESD suppressor, 18 V varistor voltage, 12 V working, 34 V clamp, 220 pF, 0.1 J.

    Key Specifications

    ParameterValue
    Orderable part numberMLVC08V012C220
    Working voltage, DC12 Vdc
    Working voltage, AC8.5 Vac
    Varistor voltage at 1 mA18 V ±15%
    Clamping voltage at 1 A34 V
    Energy absorption, 10/1000 us0.1 J
    Peak current, 8/20 us35 A
    Typical capacitance at 1 MHz220 pF
    Package0805 (2012 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11237

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    In a multilayer construction the zinc oxide grains are stacked in many thin layers, so the same body height gives a higher voltage per unit area than a single-layer disc. That is how an 0402 chip reaches 18 Vdc working voltage without becoming thick.

    The clamp column works out at 1.89 times the varistor voltage: 34 V at the rated current against 18 V at 1 mA. That ratio is what the downstream part has to survive, not the 18 V figure on the label.

    The 220 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC general type family this is item 14 of 41 in the Eaton catalogue.

    What This Family Is For

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not use a varistor as a series element or in a signal path carrying DC. It is a shunt device, and any steady current through it is a fault.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Does the clamp voltage scale with the surge current?
    Yes. The clamp column is quoted at a stated current, usually 1 A. At ten times that current the residual voltage is higher, so read the V-I curve rather than the single number when the surge is large.

    Why is the DC rating lower than the AC rating on some parts?
    It is not, on these: the AC rating is an RMS value, so the DC rating is set at the peak of that sine plus margin. Where the two look inconsistent, check which one is quoted as RMS.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products