Eaton MLVC08V014C400 14 V Multilayer Varistor
Eaton MLVC08V014C400 14 V Multilayer Varistor

Eaton MLVC08V014C400 14 V Multilayer Varistor

Share
MLVC08V014C400: multilayer varistor ESD suppressor, 20 V varistor voltage, 14 V working, 35 V clamp, 400 pF, 0.3 J.
    • Product Details
    • Download

    Eaton MLVC08V014C400 14 V Multilayer Varistor

    MLVC08V014C400 at a glance: multilayer varistor ESD suppressor, 20 V varistor voltage, 14 V working, 35 V clamp, 400 pF, 0.3 J.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMLVC08V014C400
    Working voltage, DC14 Vdc
    Working voltage, AC10 Vac
    Varistor voltage at 1 mA20 V ±10%
    Clamping voltage at 1 A35 V
    Energy absorption, 10/1000 us0.3 J
    Peak current, 8/20 us120 A
    Typical capacitance at 1 MHz400 pF
    Package0805 (2012 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    Multilayer varistors are chosen for board-level ESD and cable-transient protection where a TVS diode would add capacitance. The trade is a softer clamp: the varistor voltage tolerance is wide, so the clamp column, not the nominal voltage, sets the protection level.

    The clamp column works out at 1.75 times the varistor voltage: 35 V at the rated current against 20 V at 1 mA. That ratio is what the downstream part has to survive, not the 20 V figure on the label.

    The 400 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 2 of 97 in the Eaton catalogue.

    Series Positioning

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • Do not run the part at its varistor voltage: the working voltage column is the continuous limit, and the varistor voltage is 1.5 to 2 times higher only because the ceramic is soft at the knee.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Does the clamp voltage scale with the surge current?
    Yes. The clamp column is quoted at a stated current, usually 1 A. At ten times that current the residual voltage is higher, so read the V-I curve rather than the single number when the surge is large.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products