Eaton MLVC08V018C360 0805 Chip Varistor 18 Vdc
Eaton MLVC08V018C360 0805 Chip Varistor 18 Vdc

Eaton MLVC08V018C360 0805 Chip Varistor 18 Vdc

Share
MLVC08V018C360: multilayer varistor ESD suppressor, 25 V varistor voltage, 18 V working, 44 V clamp, 360 pF, 0.3 J.
    • Product Details
    • Download

    Eaton MLVC08V018C360 0805 Chip Varistor 18 Vdc

    MLVC08V018C360 at a glance: multilayer varistor ESD suppressor, 25 V varistor voltage, 18 V working, 44 V clamp, 360 pF, 0.3 J.

    Key Specifications

    ParameterValue
    Orderable part numberMLVC08V018C360
    Working voltage, DC18 Vdc
    Working voltage, AC12.7 Vac
    Varistor voltage at 1 mA25 V ±10%
    Clamping voltage at 1 A44 V
    Energy absorption, 10/1000 us0.3 J
    Peak current, 8/20 us100 A
    Typical capacitance at 1 MHz360 pF
    Package0805 (2012 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    Multilayer varistors are chosen for board-level ESD and cable-transient protection where a TVS diode would add capacitance. The trade is a softer clamp: the varistor voltage tolerance is wide, so the clamp column, not the nominal voltage, sets the protection level.

    The clamp column works out at 1.76 times the varistor voltage: 44 V at the rated current against 25 V at 1 mA. That ratio is what the downstream part has to survive, not the 25 V figure on the label.

    The 360 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 4 of 97 in the Eaton catalogue.

    What This Family Is For

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • A varistor is not a zener. It has no sharp knee, so it conducts a little at the working voltage and the leakage column is the honest measure of that.
    • The varistor voltage tolerance is wide by design. Two parts of the same part number can differ by 20 percent and both be good, so the design has to work at the low end of the range.

    Frequently Asked Questions

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products