Eaton MLVC08V030C150 0805 Chip Varistor 30 Vdc
Eaton MLVC08V030C150 0805 Chip Varistor 30 Vdc

Eaton MLVC08V030C150 0805 Chip Varistor 30 Vdc

Share
MLVC08V030C150: multilayer varistor ESD suppressor, 42 V varistor voltage, 30 V working, 74 V clamp, 150 pF, 0.1 J.
    • Product Details
    • Download

    Eaton MLVC08V030C150 0805 Chip Varistor 30 Vdc

    MLVC08V030C150 at a glance: multilayer varistor ESD suppressor, 42 V varistor voltage, 30 V working, 74 V clamp, 150 pF, 0.1 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMLVC08V030C150
    Working voltage, DC30 Vdc
    Working voltage, AC21.2 Vac
    Varistor voltage at 1 mA42 V ±10%
    Clamping voltage at 1 A74 V
    Energy absorption, 10/1000 us0.1 J
    Peak current, 8/20 us35 A
    Typical capacitance at 1 MHz150 pF
    Package0805 (2012 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11237

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    A multilayer varistor sits across a signal or supply rail and does nothing until the voltage crosses its breakdown point, at which it turns into a low impedance and diverts the transient. The value that matters for the protected chip is not the varistor voltage but the clamping voltage at the surge current you expect.

    The clamp column works out at 1.76 times the varistor voltage: 74 V at the rated current against 42 V at 1 mA. That ratio is what the downstream part has to survive, not the 42 V figure on the label.

    The 150 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC general type family this is item 21 of 41 in the Eaton catalogue.

    What This Family Is For

    The part goes across the line it protects, as close to the connector or the cable entry as the layout allows. Lead length matters: every extra millimetre of trace between the connector and the varistor adds inductance and raises the voltage the protected chip actually sees.

    • A varistor is not a zener. It has no sharp knee, so it conducts a little at the working voltage and the leakage column is the honest measure of that.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products