Eaton MLVC08V048C080 0805 Chip Varistor 48 Vdc
Eaton MLVC08V048C080 0805 Chip Varistor 48 Vdc

Eaton MLVC08V048C080 0805 Chip Varistor 48 Vdc

Share
MLVC08V048C080: multilayer varistor ESD suppressor, 62 V varistor voltage, 48 V working, 110 V clamp, 80 pF, 0.1 J.
    • Product Details
    • Download

    Eaton MLVC08V048C080 0805 Chip Varistor 48 Vdc

    MLVC08V048C080 at a glance: multilayer varistor ESD suppressor, 62 V varistor voltage, 48 V working, 110 V clamp, 80 pF, 0.1 J.

    Key Specifications

    ParameterValue
    Orderable part numberMLVC08V048C080
    Working voltage, DC48 Vdc
    Working voltage, AC34 Vac
    Varistor voltage at 1 mA62 V ±10%
    Clamping voltage at 1 A110 V
    Energy absorption, 10/1000 us0.1 J
    Peak current, 8/20 us35 A
    Typical capacitance at 1 MHz80 pF
    Package0805 (2012 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11237

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    In a multilayer construction the zinc oxide grains are stacked in many thin layers, so the same body height gives a higher voltage per unit area than a single-layer disc. That is how an 0402 chip reaches 18 Vdc working voltage without becoming thick.

    The clamp column works out at 1.77 times the varistor voltage: 110 V at the rated current against 62 V at 1 mA. That ratio is what the downstream part has to survive, not the 62 V figure on the label.

    The 80 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC general type family this is item 25 of 41 in the Eaton catalogue.

    Where This Series Fits

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • Do not run the part at its varistor voltage: the working voltage column is the continuous limit, and the varistor voltage is 1.5 to 2 times higher only because the ceramic is soft at the knee.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products