Eaton MLVC12V048C150 1206 Chip Varistor 48 Vdc
Eaton MLVC12V048C150 1206 Chip Varistor 48 Vdc

Eaton MLVC12V048C150 1206 Chip Varistor 48 Vdc

Share
MLVC12V048C150: multilayer varistor ESD suppressor, 62 V varistor voltage, 48 V working, 110 V clamp, 150 pF, 0.1 J.
    • Product Details
    • Download

    Eaton MLVC12V048C150 1206 Chip Varistor 48 Vdc

    MLVC12V048C150 at a glance: multilayer varistor ESD suppressor, 62 V varistor voltage, 48 V working, 110 V clamp, 150 pF, 0.1 J.

    Specification Table

    ParameterValue
    Orderable part numberMLVC12V048C150
    Working voltage, DC48 Vdc
    Working voltage, AC34 Vac
    Varistor voltage at 1 mA62 V ±10%
    Clamping voltage at 1 A110 V
    Energy absorption, 10/1000 us0.1 J
    Peak current, 8/20 us35 A
    Typical capacitance at 1 MHz150 pF
    Package1206 (3216 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11237

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    The Figures Explained

    These parts are zinc oxide ceramics sintered into a chip, so the response is faster than a junction device and there is no wear-out mechanism below the rated energy. What does degrade them is repeated energy above the rating, which shows up as a falling varistor voltage.

    The clamp column works out at 1.77 times the varistor voltage: 110 V at the rated current against 62 V at 1 mA. That ratio is what the downstream part has to survive, not the 62 V figure on the label.

    The 150 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC general type family this is item 37 of 41 in the Eaton catalogue.

    Series Positioning

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • The energy rating assumes a single pulse. Repeating the same transient heats the body faster than the datasheet curve suggests, because the curve is drawn for one event at a time.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products