Eaton MLVC18V022C1600 Multilayer Varistor, 53 V Clamp
Eaton MLVC18V022C1600 Multilayer Varistor, 53 V Clamp

Eaton MLVC18V022C1600 Multilayer Varistor, 53 V Clamp

Share
MLVC18V022C1600: multilayer varistor ESD suppressor, 30 V varistor voltage, 22 V working, 53 V clamp, 1600 pF, 2.5 J.
    • Product Details
    • Download

    Eaton MLVC18V022C1600 Multilayer Varistor, 53 V Clamp

    MLVC18V022C1600 at a glance: multilayer varistor ESD suppressor, 30 V varistor voltage, 22 V working, 53 V clamp, 1600 pF, 2.5 J.

    Key Specifications

    ParameterValue
    Orderable part numberMLVC18V022C1600
    Working voltage, DC22 Vdc
    Working voltage, AC15.6 Vac
    Varistor voltage at 1 mA30 V ±10%
    Clamping voltage at 1 A53 V
    Energy absorption, 10/1000 us2.5 J
    Peak current, 8/20 us500 A
    Typical capacitance at 1 MHz1600 pF
    Package1812 (4532 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    These parts are zinc oxide ceramics sintered into a chip, so the response is faster than a junction device and there is no wear-out mechanism below the rated energy. What does degrade them is repeated energy above the rating, which shows up as a falling varistor voltage.

    The clamp column works out at 1.77 times the varistor voltage: 53 V at the rated current against 30 V at 1 mA. That ratio is what the downstream part has to survive, not the 30 V figure on the label.

    The 1600 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 45 of 97 in the Eaton catalogue.

    Positioning in the Range

    The part goes across the line it protects, as close to the connector or the cable entry as the layout allows. Lead length matters: every extra millimetre of trace between the connector and the varistor adds inductance and raises the voltage the protected chip actually sees.

    • A varistor is not a zener. It has no sharp knee, so it conducts a little at the working voltage and the leakage column is the honest measure of that.
    • The varistor voltage tolerance is wide by design. Two parts of the same part number can differ by 20 percent and both be good, so the design has to work at the low end of the range.

    Frequently Asked Questions

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Does the clamp voltage scale with the surge current?
    Yes. The clamp column is quoted at a stated current, usually 1 A. At ten times that current the residual voltage is higher, so read the V-I curve rather than the single number when the surge is large.

    Why is the DC rating lower than the AC rating on some parts?
    It is not, on these: the AC rating is an RMS value, so the DC rating is set at the peak of that sine plus margin. Where the two look inconsistent, check which one is quoted as RMS.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products