Eaton MLVC32V056C1200 Multilayer Varistor, 127 V Clamp
Eaton MLVC32V056C1200 Multilayer Varistor, 127 V Clamp

Eaton MLVC32V056C1200 Multilayer Varistor, 127 V Clamp

Share
MLVC32V056C1200: multilayer varistor ESD suppressor, 68 V varistor voltage, 56 V working, 127 V clamp, 1200 pF, 1.3 J.
    • Product Details
    • Download

    Eaton MLVC32V056C1200 Multilayer Varistor, 127 V Clamp

    MLVC32V056C1200 at a glance: multilayer varistor ESD suppressor, 68 V varistor voltage, 56 V working, 127 V clamp, 1200 pF, 1.3 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMLVC32V056C1200
    Working voltage, DC56 Vdc
    Working voltage, AC40 Vac
    Varistor voltage at 1 mA68 V ±10%
    Clamping voltage at 1 A127 V
    Energy absorption, 10/1000 us1.3 J
    Peak current, 8/20 us100 A
    Typical capacitance at 1 MHz1200 pF
    Package3225 (8063 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data 11236

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    A chip varistor is a ceramic body with two metal terminations, so it looks like a capacitor and behaves like one until the transient arrives. That is why the capacitance column is quoted on every page: it is the parameter that decides whether the part can sit on a data line.

    The clamp column works out at 1.87 times the varistor voltage: 127 V at the rated current against 68 V at 1 mA. That ratio is what the downstream part has to survive, not the 68 V figure on the label.

    The 1200 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVC high energy family this is item 73 of 97 in the Eaton catalogue.

    Where This Series Fits

    Place it on the connector side of any series impedance. A varistor behind a common-mode choke protects the choke and not the connector, which is usually the wrong way round.

    • Do not run the part at its varistor voltage: the working voltage column is the continuous limit, and the varistor voltage is 1.5 to 2 times higher only because the ceramic is soft at the knee.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products