Eaton MLVHV0806V300 385 V Multilayer Varistor
Eaton MLVHV0806V300 385 V Multilayer Varistor

Eaton MLVHV0806V300 385 V Multilayer Varistor

Share
MLVHV0806V300: multilayer varistor ESD suppressor, 470 V varistor voltage, 385 V working, 740 V clamp, 15 pF.
    • Product Details
    • Download

    Eaton MLVHV0806V300 385 V Multilayer Varistor

    MLVHV0806V300 at a glance: multilayer varistor ESD suppressor, 470 V varistor voltage, 385 V working, 740 V clamp, 15 pF.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMLVHV0806V300
    Working voltage, AC300 Vac
    Working voltage, DC385 Vdc
    Varistor voltage at 1 mA470 V ±10%
    Leakage current at 0.8 Vvmax. 50 uA
    Clamping voltage at 1 A740 V
    Typical capacitance at 1 kHz15 pF
    Peak current, 8/20 us (1 pulse)10 A
    Peak current, 8/20 us (15 pulses)10 A
    Package0806 chip
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1239

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    The Figures Explained

    Multilayer varistors are chosen for board-level ESD and cable-transient protection where a TVS diode would add capacitance. The trade is a softer clamp: the varistor voltage tolerance is wide, so the clamp column, not the nominal voltage, sets the protection level.

    The clamp column works out at 1.57 times the varistor voltage: 740 V at the rated current against 470 V at 1 mA. That ratio is what the downstream part has to survive, not the 470 V figure on the label.

    Standing at 385 V the leakage is at most 50 uA, which is 19.25 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 15 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the MLVHV family this is item 5 of 5 in the Eaton catalogue.

    Positioning in the Range

    The part goes across the line it protects, as close to the connector or the cable entry as the layout allows. Lead length matters: every extra millimetre of trace between the connector and the varistor adds inductance and raises the voltage the protected chip actually sees.

    • Do not use a varistor as a series element or in a signal path carrying DC. It is a shunt device, and any steady current through it is a fault.
    • The capacitance column is the price of the protection: a 20000 pF part will load a high speed data line, which is why the low-capacitance versions exist at the same voltage.

    Frequently Asked Questions

    Can it protect a differential pair?
    Only with a low-capacitance part and a layout that keeps both lines symmetric. A single varistor from each line to ground is normal; one across the pair is not, because it unbalances the pair.

    What happens if the part is run above its working voltage?
    Leakage rises steeply and the body heats. A varistor is not a clamp with a sharp knee, so continuous operation above the rating is a slow degradation, not an immediate failure.

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products