Eaton MOV14V300 Radial MOV, 4500 A Surge
Eaton MOV14V300 Radial MOV, 4500 A Surge

Eaton MOV14V300 Radial MOV, 4500 A Surge

Share
MOV14V300: radial leaded metal oxide varistor, 470 V varistor voltage, 385 V working, 775 V clamp, 430 pF, 118 J.
    • Product Details
    • Download

    Eaton MOV14V300 Radial MOV, 4500 A Surge

    MOV14V300 at a glance: radial leaded metal oxide varistor, 470 V varistor voltage, 385 V working, 775 V clamp, 430 pF, 118 J.

    Key Specifications

    ParameterValue
    Orderable part numberMOV14V300
    Varistor voltage at 1 mA470 V
    Maximum continuous AC voltage300 Vrms
    Maximum continuous DC voltage385 Vdc
    Clamping voltage775 V
    Clamping current50 A
    Maximum surge current, 8/20 us4500 A
    Rated power0.6 W
    Typical capacitance at 1 kHz430 pF
    Maximum energy, 10/1000 us118 J
    Maximum body diameter5.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package14 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    For AC mains service the continuous rating is given as an RMS voltage, and the DC rating is that value multiplied by roughly 1.41. Sizing the part at or near the nominal line voltage leaves no room for regulation tolerance or a prolonged overvoltage, so the usual rule is 10 to 20 percent headroom.

    The clamp column works out at 1.65 times the varistor voltage: 775 V at the rated current against 470 V at 1 mA. That ratio is what the downstream part has to survive, not the 470 V figure on the label.

    The disc absorbs 118 J in a 10/1000 us pulse and carries 4500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.6 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 430 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 43 of 71 in the Eaton catalogue.

    What This Family Is For

    Keep the leads short and do not sleeve them together: the loop area between the two leads is part of the clamping path, and folding them against each other is what keeps the inductance low.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • The marking on the body gives the part number and the varistor voltage. In a service situation that marking is how the failed part gets identified.

    Frequently Asked Questions

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products