Eaton MOV14V350 MOV Disc Varistor 14 mm
Eaton MOV14V350 MOV Disc Varistor 14 mm

Eaton MOV14V350 MOV Disc Varistor 14 mm

Share
MOV14V350: radial leaded metal oxide varistor, 560 V varistor voltage, 460 V working, 925 V clamp, 360 pF, 125 J.
    • Product Details
    • Download

    Eaton MOV14V350 MOV Disc Varistor 14 mm

    MOV14V350 at a glance: radial leaded metal oxide varistor, 560 V varistor voltage, 460 V working, 925 V clamp, 360 pF, 125 J.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMOV14V350
    Varistor voltage at 1 mA560 V
    Maximum continuous AC voltage350 Vrms
    Maximum continuous DC voltage460 Vdc
    Clamping voltage925 V
    Clamping current50 A
    Maximum surge current, 8/20 us4500 A
    Rated power0.6 W
    Typical capacitance at 1 kHz360 pF
    Maximum energy, 10/1000 us125 J
    Maximum body diameter6 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package14 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    For AC mains service the continuous rating is given as an RMS voltage, and the DC rating is that value multiplied by roughly 1.41. Sizing the part at or near the nominal line voltage leaves no room for regulation tolerance or a prolonged overvoltage, so the usual rule is 10 to 20 percent headroom.

    The clamp column works out at 1.65 times the varistor voltage: 925 V at the rated current against 560 V at 1 mA. That ratio is what the downstream part has to survive, not the 560 V figure on the label.

    The disc absorbs 125 J in a 10/1000 us pulse and carries 4500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.6 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 360 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 45 of 71 in the Eaton catalogue.

    Positioning in the Range

    The varistor sits across the input after the fuse and before the rectifier, with short, thick traces or a direct lead-to-terminal connection. A long return path turns the trace inductance into a voltage spike that the varistor cannot clamp.

    • Do not put a varistor across a DC bus without checking the follow current: at DC there is no zero crossing to extinguish it, and the disc can overheat after the surge has passed.
    • Disc diameter sets both the energy and the lead spacing. A 20 mm part needs a 7.5 mm hole pitch, so the footprint decision comes before the electrical one.

    Frequently Asked Questions

    Are these parts UL recognised?
    Yes, the data sheet lists cURus to UL 1449 and TUV. The file numbers are on the agency page of the data sheet, and they cover the whole family.

    How do I size the disc diameter?
    From the energy, not the current. Estimate the joule content of the surge your source can deliver, add margin for repeated events, and pick the smallest disc that covers it; a larger disc also raises the capacitance across the line.

    Why is the DC rating higher than the AC rating?
    The AC rating is an RMS value, so the peak of the sine is 1.41 times higher. The DC rating is set at that peak plus margin, which is why a 130 Vac part is rated 170 Vdc.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products