Eaton MOV20V485 Radial MOV, 6500 A Surge
Eaton MOV20V485 Radial MOV, 6500 A Surge

Eaton MOV20V485 Radial MOV, 6500 A Surge

Share
MOV20V485: radial leaded metal oxide varistor, 780 V varistor voltage, 640 V working, 1290 V clamp, 510 pF, 265 J.
    • Product Details
    • Download

    Eaton MOV20V485 Radial MOV, 6500 A Surge

    MOV20V485 at a glance: radial leaded metal oxide varistor, 780 V varistor voltage, 640 V working, 1290 V clamp, 510 pF, 265 J.

    Key Specifications

    ParameterValue
    Orderable part numberMOV20V485
    Varistor voltage at 1 mA780 V
    Maximum continuous AC voltage485 Vrms
    Maximum continuous DC voltage640 Vdc
    Clamping voltage1290 V
    Clamping current100 A
    Maximum surge current, 8/20 us6500 A
    Rated power1 W
    Typical capacitance at 1 kHz510 pF
    Maximum energy, 10/1000 us265 J
    Maximum body diameter7.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    A radial disc varistor is the mains-side workhorse: it absorbs the surge that comes down the line and clamps it below the withstand of what follows. The selection is a chain of three numbers – continuous voltage, varistor voltage and energy – and the disc diameter sets all three.

    The clamp column works out at 1.65 times the varistor voltage: 1290 V at the rated current against 780 V at 1 mA. That ratio is what the downstream part has to survive, not the 780 V figure on the label.

    The disc absorbs 265 J in a 10/1000 us pulse and carries 6500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 1 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 510 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 67 of 71 in the Eaton catalogue.

    What This Family Is For

    Mount it with the body clear of the transformer and the bridge rectifier; a disc running at its rated power needs air, and the derating curve assumes it gets some.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • The marking on the body gives the part number and the varistor voltage. In a service situation that marking is how the failed part gets identified.

    Frequently Asked Questions

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Does the lead spacing matter electrically?
    It matters mechanically and for inductance. Wider spacing means a larger loop, which adds inductance in series with the clamp; the disc diameter sets the spacing, so the two choices are linked.

    What is the rated power for?
    It is the continuous dissipation the disc can take at 85 °C ambient. It matters when the varistor sits at a voltage close to its knee, not during the surge.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message