Eaton MOV20V680 Radial MOV, 6500 A Surge
Eaton MOV20V680 Radial MOV, 6500 A Surge

Eaton MOV20V680 Radial MOV, 6500 A Surge

Share
MOV20V680: radial leaded metal oxide varistor, 1100 V varistor voltage, 895 V working, 1815 V clamp, 360 pF, 383 J.
    • Product Details
    • Download

    Eaton MOV20V680 Radial MOV, 6500 A Surge

    MOV20V680 at a glance: radial leaded metal oxide varistor, 1100 V varistor voltage, 895 V working, 1815 V clamp, 360 pF, 383 J.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMOV20V680
    Varistor voltage at 1 mA1100 V
    Maximum continuous AC voltage680 Vrms
    Maximum continuous DC voltage895 Vdc
    Clamping voltage1815 V
    Clamping current100 A
    Maximum surge current, 8/20 us6500 A
    Rated power1 W
    Typical capacitance at 1 kHz360 pF
    Maximum energy, 10/1000 us383 J
    Maximum body diameter8.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1287

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    The disc is coated in epoxy and marked with the part number and the varistor voltage. Because the body is the component, the lead spacing and the disc diameter together decide the footprint – there is no separate package to shrink around it.

    The clamp column works out at 1.65 times the varistor voltage: 1815 V at the rated current against 1100 V at 1 mA. That ratio is what the downstream part has to survive, not the 1100 V figure on the label.

    The disc absorbs 383 J in a 10/1000 us pulse and carries 6500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 1 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 360 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOV family this is item 71 of 71 in the Eaton catalogue.

    Where This Series Fits

    Mount it with the body clear of the transformer and the bridge rectifier; a disc running at its rated power needs air, and the derating curve assumes it gets some.

    • A varistor that has failed short looks like a low-value resistor across the line. Always pair a mains varistor with a fuse or a thermal element.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    Why is the DC rating higher than the AC rating?
    The AC rating is an RMS value, so the peak of the sine is 1.41 times higher. The DC rating is set at that peak plus margin, which is why a 130 Vac part is rated 170 Vdc.

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products