Eaton MOVHE10V460 MOV Disc Varistor 10 mm
Eaton MOVHE10V460 MOV Disc Varistor 10 mm

Eaton MOVHE10V460 MOV Disc Varistor 10 mm

Share
MOVHE10V460: radial leaded metal oxide varistor, 750 V varistor voltage, 615 V working, 1240 V clamp, 130 pF, 100 J.
    • Product Details
    • Download

    Eaton MOVHE10V460 MOV Disc Varistor 10 mm

    MOVHE10V460 at a glance: radial leaded metal oxide varistor, 750 V varistor voltage, 615 V working, 1240 V clamp, 130 pF, 100 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMOVHE10V460
    Varistor voltage at 1 mA750 V
    Maximum continuous AC voltage460 Vrms
    Maximum continuous DC voltage615 Vdc
    Clamping voltage1240 V
    Clamping current25 A
    Maximum surge current, 8/20 us3500 A
    Rated power0.4 W
    Typical capacitance at 1 kHz130 pF
    Maximum energy, 10/1000 us100 J
    Maximum body diameter6.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package10 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1288

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    This is a single-shot device in the sense that the joule rating is quoted for one pulse. A surge protector built around a disc survives because the pulses are rare, not because the part is unlimited; the derating curve states how many.

    The clamp column works out at 1.65 times the varistor voltage: 1240 V at the rated current against 750 V at 1 mA. That ratio is what the downstream part has to survive, not the 750 V figure on the label.

    The disc absorbs 100 J in a 10/1000 us pulse and carries 3500 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 0.4 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 130 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOVHE family this is item 30 of 71 in the Eaton catalogue.

    Positioning in the Range

    Mount it with the body clear of the transformer and the bridge rectifier; a disc running at its rated power needs air, and the derating curve assumes it gets some.

    • Do not put a varistor across a DC bus without checking the follow current: at DC there is no zero crossing to extinguish it, and the disc can overheat after the surge has passed.
    • The epoxy coating is the insulation, so the lead bend radius and the mounting clip both matter: a cracked coating at the lead exit is a failure point.

    Frequently Asked Questions

    What happens at end of life?
    A varistor that absorbs more than its rating drifts low in voltage and eventually fails short. That is why a fuse or a thermal element is placed in series with it on mains inputs.

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products