Eaton MOVHE20V460 MOV Disc Varistor 20 mm
Eaton MOVHE20V460 MOV Disc Varistor 20 mm

Eaton MOVHE20V460 MOV Disc Varistor 20 mm

Share
MOVHE20V460: radial leaded metal oxide varistor, 750 V varistor voltage, 615 V working, 1240 V clamp, 530 pF, 420 J.
    • Product Details
    • Download

    Eaton MOVHE20V460 MOV Disc Varistor 20 mm

    MOVHE20V460 at a glance: radial leaded metal oxide varistor, 750 V varistor voltage, 615 V working, 1240 V clamp, 530 pF, 420 J.

    Specification Table

    ParameterValue
    Orderable part numberMOVHE20V460
    Varistor voltage at 1 mA750 V
    Maximum continuous AC voltage460 Vrms
    Maximum continuous DC voltage615 Vdc
    Clamping voltage1240 V
    Clamping current100 A
    Maximum surge current, 8/20 us10000 A
    Rated power1 W
    Typical capacitance at 1 kHz530 pF
    Maximum energy, 10/1000 us420 J
    Maximum body diameter7.5 mm
    Agency recognitioncURus (UL 1449) and TUV
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1288

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    This is a single-shot device in the sense that the joule rating is quoted for one pulse. A surge protector built around a disc survives because the pulses are rare, not because the part is unlimited; the derating curve states how many.

    The clamp column works out at 1.65 times the varistor voltage: 1240 V at the rated current against 750 V at 1 mA. That ratio is what the downstream part has to survive, not the 750 V figure on the label.

    The disc absorbs 420 J in a 10/1000 us pulse and carries 10000 A in an 8/20 us pulse. Those are single shot figures: the same part will take a fraction of the energy repeatedly.

    At 1 W continuous rating the body can sit at the working voltage indefinitely. A 20 mm disc handles roughly 530 pF across the line, which matters on a signal-carrying pair but not on a mains input.

    Within the MOVHE family this is item 66 of 71 in the Eaton catalogue.

    What This Family Is For

    Mount it with the body clear of the transformer and the bridge rectifier; a disc running at its rated power needs air, and the derating curve assumes it gets some.

    • The clamping voltage is quoted at a test current that is far below the surge. At the full 8/20 rating the residual voltage is higher – read the V-I curve.
    • The marking on the body gives the part number and the varistor voltage. In a service situation that marking is how the failed part gets identified.

    Frequently Asked Questions

    Can it be used on a DC bus?
    Yes, within the DC rating, but the energy per event is usually larger because there is no zero crossing to help extinguish the follow current. Check the application note before using a mains part on a high-voltage DC bus.

    How do I choose between 130 V and 150 V for a 120 V line?
    On a 120 V nominal line the steady-state RMS can reach 132 V or more, so a 130 Vac part has no headroom. The 150 V part is the usual choice, and the varistor voltage that comes with it is still below the withstand of most downstream parts.

    Does the lead spacing matter electrically?
    It matters mechanically and for inductance. Wider spacing means a larger loop, which adds inductance in series with the clamp; the disc diameter sets the spacing, so the two choices are linked.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products