Eaton MOVS2825V360 SMT Varistor, 400 A Peak
Eaton MOVS2825V360 SMT Varistor, 400 A Peak

Eaton MOVS2825V360 SMT Varistor, 400 A Peak

Share
MOVS2825V360: surface mount metal oxide varistor, 522-638 V varistor voltage, 470 V working, 920 V clamp, 40 pF, 16.5 J.
    • Product Details
    • Download

    Eaton MOVS2825V360 SMT Varistor, 400 A Peak

    MOVS2825V360 at a glance: surface mount metal oxide varistor, 522-638 V varistor voltage, 470 V working, 920 V clamp, 40 pF, 16.5 J.

    Specification Table

    ParameterValue
    Orderable part numberMOVS2825V360
    Working voltage, RMS360 Vrms
    Working voltage, DC470 Vdc
    Varistor voltage at 1 mA522-638 V
    Leakage current at 0.8 Vvmax. 50 uA
    Clamping voltage, 8/20 us920 V
    Peak current, 8/20 us400 A
    Maximum energy, 10/1000 us16.5 J
    Rated power0.1 W
    Typical capacitance at 1 kHz40 pF
    Component thickness5.6 mm
    Package2825
    MountingSurface mount
    Operating temperature-40 °C to +85 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1005

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    How to Read These Ratings

    Selection follows the same chain as a radial part: continuous voltage first, then varistor voltage, then the energy the transient actually delivers. The clamp column tells you what the downstream circuit sees at the rated current.

    The clamp column works out at 1.76 times the varistor voltage: 920 V at the rated current against 522~638 V at 1 mA. That ratio is what the downstream part has to survive, not the 522~638 V figure on the label.

    Standing at 470 V the leakage is at most 50 uA, which is 23.5 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    At 5.6 mm tall this is the part that has to fit under the enclosure. The 16.5 J rating and the 400 A peak come from a body that size, so a lower profile in the same footprint would mean less energy.

    Within the MOVS2825 family this is item 25 of 27 in the Eaton catalogue.

    What This Family Is For

    The pad is the heatsink. Use the recommended land pattern even when the board is tight; a reduced pad raises the body temperature at the same continuous current.

    • Do not stack a chip varistor on a via-in-pad without filling it: the solder wicking changes the joint and the thermal path at the same time.
    • The 2825 and 4032 bodies are thick enough that the pick-and-place nozzle needs the right tip; a standard 0402 nozzle will not hold them.

    Frequently Asked Questions

    What is the peak current rating for?
    It is the 8/20 microsecond single-shot current the body survives. The energy column is the better guide for a long pulse, because a 10/1000 microsecond waveform delivers far more joules at the same peak.

    Why is the capacitance so high?
    A 4032 body at 14 Vdc has a large electrode area and a thin dielectric, so the capacitance runs into thousands of picofarads. That is fine on a supply rail and not fine on a data line.

    Can two parts be paralleled for more energy?
    Only if they are matched, which they are not. The varistor voltage tolerance means one part takes most of the current, so the pair behaves like the weaker one plus a little.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message