Eaton MOVTP14V275N Protected MOV 14 mm, 2-Lead
Eaton MOVTP14V275N Protected MOV 14 mm, 2-Lead

Eaton MOVTP14V275N Protected MOV 14 mm, 2-Lead

Share
MOVTP14V275N: thermally protected metal oxide varistor, 387-473 V varistor voltage, 350 V working, 710 V clamp, 170 J.
    • Product Details
    • Download

    Eaton MOVTP14V275N Protected MOV 14 mm, 2-Lead

    MOVTP14V275N at a glance: thermally protected metal oxide varistor, 387-473 V varistor voltage, 350 V working, 710 V clamp, 170 J.

    Key Specifications

    ParameterValue
    Orderable part numberMOVTP14V275N
    Working voltage, DC350 Vdc
    Working voltage, AC275 Vac
    Varistor voltage at 1 mA387 V to 473 V
    Clamping voltage, 8/20 us710 V at 50 A
    Energy absorption, 10/1000 us170 J
    Rated power0.6 W
    Peak current, 8/20 us6000 A
    Impulse response timeunder 25 ns
    Leakage current at 0.75 V1mAmax. 20 uA
    Pin form2-lead, no status contact
    Package14 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +105 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1079

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    The failure mode this addresses is real: an overloaded MOV can fail short and then draw enough current to overheat the board. The thermal element is the difference between a protected input and a fire risk, which is why these parts appear in white goods and power supplies rather than on signal lines.

    The clamp column works out at 1.65 times the varistor voltage: 710 V at the rated current against 430 V at 1 mA. That ratio is what the downstream part has to survive, not the 430 V figure on the label.

    Standing at 350 V the leakage is at most 20 uA, which is 7 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The thermal element is the difference from a plain disc of the same rating. If the body overheats the element opens at 0.6 W of continuous overload, before the epoxy and the board around it are damaged.

    The 2-lead form is the mechanical difference: two leads replace a plain disc one for one. The electrical table is identical for both.

    Within the MOVTP family this is item 7 of 28 in the Eaton catalogue.

    Positioning in the Range

    The protected part goes across the input downstream of the fuse, with the body clear of other heat sources. In the three-lead version the third pin is a signal, not a current path, and should be routed to the monitoring circuit rather than tied to ground.

    • After the element opens, the circuit has no protection at all. The monitoring signal exists so the board can be taken out of service rather than run unprotected.
    • Agency recognition covers the varistor; the thermal element is part of the same approval and does not need a separate file.

    Frequently Asked Questions

    Does it reset after operation?
    No. The element is one-shot, like a fuse. Once it opens the board has to be repaired, which is the intended behaviour: the alternative is a shorted MOV heating the board.

    Is the electrical rating different from an unprotected MOV?
    No, the disc inside is the same. The thermal element adds series resistance of a few milliohms and takes space, but the voltage and energy ratings are unchanged.

    How fast does it trip?
    The thermal path takes seconds, not microseconds. It is designed for the overload that follows a shorted varistor, not for the surge itself – the surge is handled by the disc.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products