Eaton MOVTP14V320N Protected MOV 14 mm, 2-Lead
Eaton MOVTP14V320N Protected MOV 14 mm, 2-Lead

Eaton MOVTP14V320N Protected MOV 14 mm, 2-Lead

Share
MOVTP14V320N: thermally protected metal oxide varistor, 459-561 V varistor voltage, 410 V working, 845 V clamp, 209 J.
    • Product Details
    • Download

    Eaton MOVTP14V320N Protected MOV 14 mm, 2-Lead

    MOVTP14V320N at a glance: thermally protected metal oxide varistor, 459-561 V varistor voltage, 410 V working, 845 V clamp, 209 J.

    Specification Table

    ParameterValue
    Orderable part numberMOVTP14V320N
    Working voltage, DC410 Vdc
    Working voltage, AC320 Vac
    Varistor voltage at 1 mA459 V to 561 V
    Clamping voltage, 8/20 us845 V at 50 A
    Energy absorption, 10/1000 us209 J
    Rated power0.6 W
    Peak current, 8/20 us6000 A
    Impulse response timeunder 25 ns
    Leakage current at 0.75 V1mAmax. 20 uA
    Pin form2-lead, no status contact
    Package14 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +105 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1079

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    A thermally protected varistor adds a fuse or a spring-loaded contact inside the same package. When the body overheats – the end state of a varistor that has absorbed more than it can take – the element opens and removes the part from the circuit instead of letting it sit in a low-resistance failure mode.

    The clamp column works out at 1.66 times the varistor voltage: 845 V at the rated current against 510 V at 1 mA. That ratio is what the downstream part has to survive, not the 510 V figure on the label.

    Standing at 410 V the leakage is at most 20 uA, which is 8.2 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The thermal element is the difference from a plain disc of the same rating. If the body overheats the element opens at 0.6 W of continuous overload, before the epoxy and the board around it are damaged.

    The 2-lead form is the mechanical difference: two leads replace a plain disc one for one. The electrical table is identical for both.

    Within the MOVTP family this is item 11 of 28 in the Eaton catalogue.

    Positioning in the Range

    Leave the clearance the drawing asks for. The thermal element is inside the package, but the heat that trips it has to come from the body, and a part pressed against a heatsink or a capacitor sees the wrong temperature.

    • The third lead is not a second ground. Wiring it to the return defeats the monitoring function and can hold the thermal contact closed.
    • The response time is quoted for the thermal element, not for the varistor. The electrical clamp happens in nanoseconds; the thermal trip takes seconds.

    Frequently Asked Questions

    Does the third lead carry current?
    No. It is a signal contact rated for a monitoring circuit, typically a few milliamps at low voltage. It should not be used to carry the load current.

    Can it be used on a DC input?
    The varistor part can, within its DC rating. The thermal element does not care about the waveform, so the DC limitation is the same as for any MOV: the follow current has no zero crossing.

    What approvals does it carry?
    The data sheet lists the agency file for the family. The thermal element is covered by the same approval as the varistor inside.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products