Eaton MOVTP20V250N Protected MOV 20 mm, 2-Lead
Eaton MOVTP20V250N Protected MOV 20 mm, 2-Lead

Eaton MOVTP20V250N Protected MOV 20 mm, 2-Lead

Share
MOVTP20V250N: thermally protected metal oxide varistor, 351-429 V varistor voltage, 320 V working, 650 V clamp, 240 J.
    • Product Details
    • Download

    Eaton MOVTP20V250N Protected MOV 20 mm, 2-Lead

    MOVTP20V250N at a glance: thermally protected metal oxide varistor, 351-429 V varistor voltage, 320 V working, 650 V clamp, 240 J.

    Specification Table

    ParameterValue
    Orderable part numberMOVTP20V250N
    Working voltage, DC320 Vdc
    Working voltage, AC250 Vac
    Varistor voltage at 1 mA351 V to 429 V
    Clamping voltage, 8/20 us650 V at 100 A
    Energy absorption, 10/1000 us240 J
    Rated power1 W
    Peak current, 8/20 us10000 A
    Impulse response timeunder 25 ns
    Leakage current at 0.75 V1mAmax. 20 uA
    Pin form2-lead, no status contact
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +105 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1079

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    The electrical ratings match an unprotected part of the same disc size, so the selection is unchanged. What changes is the space around the part: the thermal element needs clearance and the third lead needs a route.

    The clamp column works out at 1.67 times the varistor voltage: 650 V at the rated current against 390 V at 1 mA. That ratio is what the downstream part has to survive, not the 390 V figure on the label.

    Standing at 320 V the leakage is at most 20 uA, which is 6.4 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The thermal element is the difference from a plain disc of the same rating. If the body overheats the element opens at 1 W of continuous overload, before the epoxy and the board around it are damaged.

    The 2-lead form is the mechanical difference: two leads replace a plain disc one for one. The electrical table is identical for both.

    Within the MOVTP family this is item 19 of 28 in the Eaton catalogue.

    Positioning in the Range

    The protected part goes across the input downstream of the fuse, with the body clear of other heat sources. In the three-lead version the third pin is a signal, not a current path, and should be routed to the monitoring circuit rather than tied to ground.

    • The third lead is not a second ground. Wiring it to the return defeats the monitoring function and can hold the thermal contact closed.
    • The part is a through-hole component with a defined lead form, so the hole pattern and the body height both come from the drawing.

    Frequently Asked Questions

    What approvals does it carry?
    The data sheet lists the agency file for the family. The thermal element is covered by the same approval as the varistor inside.

    What exactly opens inside the part?
    A thermal element – a fuse or a spring contact – that is thermally coupled to the varistor body. When the body exceeds its limit the element opens and the part becomes an open circuit instead of a short.

    Should I use the two-lead or the three-lead version?
    Two-lead where the part only has to protect. Three-lead where the status has to be reported: the third pin carries the thermal contact out so a monitoring circuit can see that the protector has operated.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products