Eaton MOVTP20V300N Protected MOV 20 mm, 2-Lead
Eaton MOVTP20V300N Protected MOV 20 mm, 2-Lead

Eaton MOVTP20V300N Protected MOV 20 mm, 2-Lead

Share
MOVTP20V300N: thermally protected metal oxide varistor, 423-517 V varistor voltage, 385 V working, 775 V clamp, 350 J.
    • Product Details
    • Download

    Eaton MOVTP20V300N Protected MOV 20 mm, 2-Lead

    MOVTP20V300N at a glance: thermally protected metal oxide varistor, 423-517 V varistor voltage, 385 V working, 775 V clamp, 350 J.

    Electrical Specifications

    ParameterValue
    Orderable part numberMOVTP20V300N
    Working voltage, DC385 Vdc
    Working voltage, AC300 Vac
    Varistor voltage at 1 mA423 V to 517 V
    Clamping voltage, 8/20 us775 V at 100 A
    Energy absorption, 10/1000 us350 J
    Rated power1 W
    Peak current, 8/20 us10000 A
    Impulse response timeunder 25 ns
    Leakage current at 0.75 V1mAmax. 20 uA
    Pin form2-lead, no status contact
    Package20 mm disc
    MountingRadial, through-hole
    Operating temperature-40 °C to +105 °C
    QualificationCommercial grade
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1079

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    The electrical ratings match an unprotected part of the same disc size, so the selection is unchanged. What changes is the space around the part: the thermal element needs clearance and the third lead needs a route.

    The clamp column works out at 1.65 times the varistor voltage: 775 V at the rated current against 470 V at 1 mA. That ratio is what the downstream part has to survive, not the 470 V figure on the label.

    Standing at 385 V the leakage is at most 20 uA, which is 7.7 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The thermal element is the difference from a plain disc of the same rating. If the body overheats the element opens at 1 W of continuous overload, before the epoxy and the board around it are damaged.

    The 2-lead form is the mechanical difference: two leads replace a plain disc one for one. The electrical table is identical for both.

    Within the MOVTP family this is item 23 of 28 in the Eaton catalogue.

    Series Positioning

    In the three-lead version the third pin should be treated as a low-voltage signal: it is isolated from the line, but it runs close to it, so keep the creepage of the monitoring track in mind.

    • The thermal element protects against a shorted varistor, not against overvoltage. It does not replace the fuse, and it does not reset: once it opens the part is finished.
    • The two-lead and three-lead versions share the electrical table, so the ordering code suffix is the only difference between them.

    Frequently Asked Questions

    Does it reset after operation?
    No. The element is one-shot, like a fuse. Once it opens the board has to be repaired, which is the intended behaviour: the alternative is a shorted MOV heating the board.

    Is the electrical rating different from an unprotected MOV?
    No, the disc inside is the same. The thermal element adds series resistance of a few milliohms and takes space, but the voltage and energy ratings are unchanged.

    How fast does it trip?
    The thermal path takes seconds, not microseconds. It is designed for the overload that follows a shorted varistor, not for the surge itself – the surge is handled by the disc.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products