Eaton MP2-1R0-R 1.0 uH Shielded Inductor 103 mOhm
Eaton MP2-1R0-R 1.0 uH Shielded Inductor 103 mOhm

Eaton MP2-1R0-R 1.0 uH Shielded Inductor 103 mOhm

Share
MP2-1R0-R: high-current power inductor, 1.0 uH, 1.67 A, Isat 2.1 A, DCR 103 mOhm.
    • Product Details
    • Download

    Eaton MP2-1R0-R 1.0 uH Shielded Inductor 103 mOhm

    MP2-1R0-R at a glance: high-current power inductor, 1.0 uH, 1.67 A, Isat 2.1 A, DCR 103 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMP2-1R0-R
    Inductance1.0 uH ±20%
    Q minimum20
    DCR maximum @ +25 °C103 mOhm
    Irms (DC, 40 °C rise)1.67 A
    Isat2.1 A
    SRF typical160 MHz
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4108

    Mechanical Drawing

    MP2-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4108: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    The part is built around a distributed-gap core: the energy is stored through the volume of the magnetic material rather than in a single discrete gap, which is what produces the gradual rolloff and the low fringing field. Copper loss and core loss are traded against each other in the winding and body proportions.

    At 1.67 A the winding dissipates about 0.287 W in copper, using the 103 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 2.1 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the MP2 family this is value 2 of 12, in a range that runs from 0.47 to 47 uH.

    Series Positioning

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: pc cards,; mobile phones; disk drives; gps systems.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products