Eaton MP2-4R7-R 4.7 uH Shielded Inductor 180 mOhm
Eaton MP2-4R7-R 4.7 uH Shielded Inductor 180 mOhm

Eaton MP2-4R7-R 4.7 uH Shielded Inductor 180 mOhm

Share
MP2-4R7-R: high-current power inductor, 4.7 uH, 1.18 A, Isat 1 A, DCR 180 mOhm.
    • Product Details
    • Download

    Eaton MP2-4R7-R 4.7 uH Shielded Inductor 180 mOhm

    MP2-4R7-R at a glance: high-current power inductor, 4.7 uH, 1.18 A, Isat 1 A, DCR 180 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMP2-4R7-R
    Inductance4.7 uH ±20%
    Q minimum46
    DCR maximum @ +25 °C180 mOhm
    Irms (DC, 40 °C rise)1.18 A
    Isat1 A
    SRF typical130 MHz
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4108

    Outline Drawing

    MP2-4R7-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4108: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    The part is built around a distributed-gap core: the energy is stored through the volume of the magnetic material rather than in a single discrete gap, which is what produces the gradual rolloff and the low fringing field. Copper loss and core loss are traded against each other in the winding and body proportions.

    At 1.18 A the winding dissipates about 0.251 W in copper, using the 180 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 1 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the MP2 family this is value 6 of 12, in a range that runs from 0.47 to 47 uH.

    Where This Series Fits

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: pc cards,; mobile phones; disk drives; gps systems.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    What is the difference between Irms and Isat?
    Irms is the DC current that produces the rated temperature rise. Isat is the peak current at which inductance has fallen by a defined percentage. A converter can run above Irms briefly but must stay inside Isat.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products