Eaton MPI4040R1-1R0-R 1.0 uH Power Inductor, 3.7 A
Eaton MPI4040R1-1R0-R 1.0 uH Power Inductor, 3.7 A

Eaton MPI4040R1-1R0-R 1.0 uH Power Inductor, 3.7 A

Share
MPI4040R1-1R0-R: high-current power inductor, 1.0 uH, 3.7 A, Isat 7.7 A, DCR 40 mOhm.
    • Product Details
    • Download

    Eaton MPI4040R1-1R0-R 1.0 uH Power Inductor, 3.7 A

    MPI4040R1-1R0-R at a glance: high-current power inductor, 1.0 uH, 3.7 A, Isat 7.7 A, DCR 40 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMPI4040R1-1R0-R
    Inductance1.0 uH ±20%
    DCR maximum @ +25 °C40 mOhm
    Irms (DC, 40 °C rise)3.7 A
    Isat7.7 A
    K-factor990
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4086

    Mechanical Drawing

    MPI4040R1-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4086: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    How to Read These Ratings

    A shielded power inductor with a soft saturation curve: as the current rises the inductance droops rather than collapsing, so the regulator keeps control through a load transient. The molded body contains the field, which is why these parts can sit side by side on a multiphase rail without coupling into each other.

    At 3.7 A the winding dissipates about 0.548 W in copper, using the 40 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 7.7 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the MPI4040R1 family this is value 7 of 11, in a range that runs from 0.1 to 4.7 uH.

    What This Family Is For

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: handheld/mobile devices; portable media players; gps/pdas; mp3 players; battery operated devices.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message