Eaton MPI4040R1-2R2-R 2.2 uH Inductor, Isat 5.9 A
Eaton MPI4040R1-2R2-R 2.2 uH Inductor, Isat 5.9 A

Eaton MPI4040R1-2R2-R 2.2 uH Inductor, Isat 5.9 A

Share
MPI4040R1-2R2-R: high-current power inductor, 2.2 uH, 2.6 A, Isat 5.9 A, DCR 80 mOhm.
    • Product Details
    • Download

    Eaton MPI4040R1-2R2-R 2.2 uH Inductor, Isat 5.9 A

    MPI4040R1-2R2-R at a glance: high-current power inductor, 2.2 uH, 2.6 A, Isat 5.9 A, DCR 80 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMPI4040R1-2R2-R
    Inductance2.2 uH ±20%
    DCR maximum @ +25 °C80 mOhm
    Irms (DC, 40 °C rise)2.6 A
    Isat5.9 A
    K-factor623
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 4086

    Dimensions and Pad Layout

    MPI4040R1-2R2-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 4086: outline with rated mm dimensions, pad layout and marking. Tolerances are stated on the drawing.

    What the Numbers Mean

    The part is built around a distributed-gap core: the energy is stored through the volume of the magnetic material rather than in a single discrete gap, which is what produces the gradual rolloff and the low fringing field. Copper loss and core loss are traded against each other in the winding and body proportions.

    At 2.6 A the winding dissipates about 0.541 W in copper, using the 80 mOhm figure. That is the DC floor of the loss budget: ripple and core loss come on top of it.

    Saturation is reached at 5.9 A. Beyond that point the inductance falls on the soft part of the curve, and the converter’s ripple grows faster than the load current does.

    Within the MPI4040R1 family this is value 9 of 11, in a range that runs from 0.1 to 4.7 uH.

    Positioning in the Range

    The power inductor family covers sub-microhenry to tens of microhenry at currents from a few amps to tens of amps, in shielded surface-mount bodies. The data sheet rows carry both typical and maximum DCR so the loss budget can be built either way.

    • DCR is quoted at +20 °C. Copper resistance rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: handheld/mobile devices; portable media players; gps/pdas; mp3 players; battery operated devices.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three different numbers, three different checks.

    Frequently Asked Questions

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough to place parts side by side on a multiphase rail.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL, not with the zero-bias value.

    Why are there two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products