Eaton MPIA2510V2-R33-R 0.33 uH Shielded Power Inductor
Eaton MPIA2510V2-R33-R 0.33 uH Shielded Power Inductor

Eaton MPIA2510V2-R33-R 0.33 uH Shielded Power Inductor

Share
MPIA2510V2-R33-R: automotive power inductor, 0.33 uH , 4.8 A Irms, Isat 6.6 A, DCR 15 mOhm.
    • Product Details
    • Download

    Eaton MPIA2510V2-R33-R 0.33 uH Shielded Power Inductor

    MPIA2510V2-R33-R at a glance: automotive power inductor, 0.33 uH , 4.8 A Irms, Isat 6.6 A, DCR 15 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberMPIA2510V2-R33-R
    Inductance0.33 uH
    DCR typical @ +20 °C15 mOhm
    DCR maximum @ +20 °C20 mOhm
    Irms (DC, 40 °C rise)4.8 A
    Isat6.6 A
    SRF typical120 MHz
    K-factor6336
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10650

    Mechanical Drawing

    MPIA2510V2-R33-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10650: outline with
    rated mm dimensions, pad layout and marking.

    How to Read These Ratings

    A molded automotive power inductor with a soft saturation curve: as current rises the inductance droops instead of collapsing, so a converter keeps control through a load step. The body is molded around the winding, which contains the field.

    At 4.8 A the winding dissipates about 0.346 W in copper using the typical DCR of 15 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 7.19 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 120 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 6336 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MPIA2510V2 family this is value 1 of 7, in a range from 0.33 uH to 3.3 uH.

    Where This Series Fits

    The MPIA family is the automotive miniature power range: AEC-Q200 qualified, low profile, in sizes from 2 mm to 4 mm, with both typical and maximum DCR quoted for every row.

    • DCR is quoted at +20 °C; copper rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps, interior lighting and led lighting; doors, window lift and seat control.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three numbers, three checks.

    Frequently Asked Questions

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    What is the difference between Irms and Isat?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough for dense layouts.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message