Eaton MPIA4012V2-1R0-R 1 uH AEC-Q200 Inductor 38.5 mOhm
Eaton MPIA4012V2-1R0-R 1 uH AEC-Q200 Inductor 38.5 mOhm

Eaton MPIA4012V2-1R0-R 1 uH AEC-Q200 Inductor 38.5 mOhm

Share
MPIA4012V2-1R0-R: automotive power inductor, 1 uH , 4.3 A Irms, Isat 6.5 A, DCR 38.5 mOhm.
    • Product Details
    • Download

    Eaton MPIA4012V2-1R0-R 1 uH AEC-Q200 Inductor 38.5 mOhm

    MPIA4012V2-1R0-R at a glance: automotive power inductor, 1 uH , 4.3 A Irms, Isat 6.5 A, DCR 38.5 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberMPIA4012V2-1R0-R
    Inductance1 uH
    DCR typical @ +20 °C38.5 mOhm
    Irms (DC, 40 °C rise)4.3 A
    Isat6.5 A
    SRF typical46.5 MHz
    K-factor64
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10652

    Dimensions and Pad Layout

    MPIA4012V2-1R0-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10652: outline with
    rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    A molded automotive power inductor with a soft saturation curve: as current rises the inductance droops instead of collapsing, so a converter keeps control through a load step. The body is molded around the winding, which contains the field.

    At 4.3 A the winding dissipates about 0.712 W in copper using the typical DCR of 38.5 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 21.1 uJ at the saturation point, which is the energy available to bridge a load step.

    Self-resonance is 46.5 MHz typical. Keep the operating band, and the harmonics that carry energy, below it.

    The K-factor of 64 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MPIA4012V2 family this is value 4 of 7, in a range from 0.33 uH to 4.7 uH.

    Positioning in the Range

    The MPIA family is the automotive miniature power range: AEC-Q200 qualified, low profile, in sizes from 2 mm to 4 mm, with both typical and maximum DCR quoted for every row.

    • DCR is quoted at +20 °C; copper rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: body electronics; central body control module; vehicle access control system; headlamps, tail lamps and interior lighting; doors, window lift and seat control.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three numbers, three checks.

    Frequently Asked Questions

    What is the difference between Irms and Isat?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    How much inductance is left at rated current?
    The FLL column gives the inductance at saturation current. Ripple at full load should be calculated with FLL.

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products