Eaton MPIA4040R3-6R8-R 6.8 uH AEC-Q200 Inductor 120 mOhm
Eaton MPIA4040R3-6R8-R 6.8 uH AEC-Q200 Inductor 120 mOhm

Eaton MPIA4040R3-6R8-R 6.8 uH AEC-Q200 Inductor 120 mOhm

Share
MPIA4040R3-6R8-R: automotive power inductor, 6.8 uH , 2 A Irms, Isat 4.5 A, DCR 120 mOhm.
    • Product Details
    • Download

    Eaton MPIA4040R3-6R8-R 6.8 uH AEC-Q200 Inductor 120 mOhm

    MPIA4040R3-6R8-R at a glance: automotive power inductor, 6.8 uH , 2 A Irms, Isat 4.5 A, DCR 120 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberMPIA4040R3-6R8-R
    Inductance6.8 uH
    DCR typical @ +20 °C120 mOhm
    Irms (DC, 40 °C rise)2 A
    Isat4.5 A
    K-factor306
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, -R suffix
    Data sheetEaton Technical Data 10230

    Dimensions and Pad Layout

    MPIA4040R3-6R8-R mechanical dimensions and pad layout

    Drawing reproduced from Eaton Technical Data 10230: outline with
    rated mm dimensions, pad layout and marking.

    What the Numbers Mean

    The part is built for automotive DC-DC stages: AEC-Q200 qualified, shielded, and characterised with both typical and maximum DCR so the loss budget can be built on either figure.

    At 2 A the winding dissipates about 0.48 W in copper using the typical DCR of 120 mOhm. That is the DC floor of the loss budget – ripple and core loss come on top.

    The core stores about 68.8 uJ at the saturation point, which is the energy available to bridge a load step.

    The K-factor of 306 converts inductance and ripple into flux swing; read the core-loss curve at that amplitude.

    Within the MPIA4040R3 family this is value 8 of 10, in a range from 0.22 uH to 15 uH.

    Where This Series Fits

    The MPIA family is the automotive miniature power range: AEC-Q200 qualified, low profile, in sizes from 2 mm to 4 mm, with both typical and maximum DCR quoted for every row.

    • DCR is quoted at +20 °C; copper rises about 0.4 % per °C, so the hot loss is higher than the cold figure.
    • Typical applications: body electronics – central body control module – vehicle access control system – headlamps, tail lamps and interior lighting – door control; chassis and safety electronics – airbag control unit.
    • Design note: ripple from OCL, thermal from Irms, transient from Isat. Three numbers, three checks.

    Frequently Asked Questions

    Is the part shielded?
    The molded body encloses the winding, so the external field is small enough for dense layouts.

    What is the difference between Irms and Isat?
    Irms is the DC current for the rated temperature rise; Isat is the peak current at a defined inductance rolloff. A converter can exceed Irms briefly but must stay inside Isat.

    Why two DCR columns?
    Typical and maximum. A guaranteed thermal design uses the maximum; a nominal efficiency calculation can use the typical.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products